Build your own raku kiln or fix your gas kiln with new brick, Kaowool, pyrometers, cement and more.
Items 1-25 of 25

Board Ld 24" x 48" x 1/2" 2300° F

Kaowool Board 1/2 thick Low Density, 24" x 48"
  • Original Price: $88.16
  • You Save: $8.82
  • $79.34
  • Availability: 1

Fiber Paper 1/16" Thick Sold by sq ft

Fiber Paper 1/16 Thick 12" X 24"W 2300°F, sold by the square foot. Use to keep flat glass from sticking to the kiln shelf. Can be used for any glass fusing or jewelery firing as a shelf liner. May be used to prevent porcelain from sticking to the kilnwash. The binder in the paper burns out on first firing causing a little smoke. Buy 50 Square feet get 20% discount.
  • $3.88
  • Availability: 18

Brick 2300`F Soft 9" x 4.5" x 2.5" 12 Ca

Brick 2300`F Soft 9" X 4.5" X 2.5" is used for constructing kilns, this is the most common insulating brick used in kiln building. It is very soft and easily cut with hand tools. Can be used as a soldering block. Buy 25 get 20% off. You will need 25 to make a base for a raku kiln.
  • $6.50
  • Availability: 29

Brick 2600`F Soft 9" x 4.5" x 2.5"

Brick 2600`F Soft 9" X 4.5" X 2.5" is used for constructing kilns, this is a high heat brick used in bag walls or for hot areas of the kiln. It is soft and easily cut with hand tools. Can be used as a soldering block. Buy 25 get 20% off.
  • $7.85
  • Availability: 3

Brick 3000`F Dense Hard Brick

Brick 3000`F Dense Hard Brick 9" X 4.5" X 2.5" is used for constructing kilns, this is the most common non insulating brick used in kiln building. It is very hard and difficult to cut. Buy 25 get 20% off.
  • $9.52
  • Availability: 55

Max-Wool Thick 2300`F 8 Lbs/cuft

Cerablanket fiber blanket 1" thick, 8 pound, 2400F Max.

Comes on a roll 2 feet wide and 25 ft long. Sold by the square foot. 12" x 12" Buy 50 feet for a full roll and get 20% off.
Use to make a raku kiln, make a heat shield for your muffler, also called Prop or Propit for supporting porcelain in cone 6 firing.
Can be used to make glass fusing mold (use the rigidizer to make the blanket stiff)

  • Produced from high purity Alumina - Silica spun fiber.
  • Contains no organic binders.
  • Low thermal conductivity and heat storage.
  • Resistant to thermal shock and chemical attack.
  • Good acoustical characteristics.
  • Highly flexible; easily cut, fabricated and installed.
  • 2400 F maximum temperature rating
  • Wear Gloves, long sleeves and a respirator when handling!
  • Original Price: $3.95
  • You Save: $0.39
  • $3.56
  • Availability: 100

Thermocouple 10" *Only*

10" Replacement Thermocouple

  • Heavy duty 8 Gauge
  • 10" long
  • Type K 2350F
  • Includes porcelain mounting block
  • $41.00
  • Availability: 3

Thermocouple 12" *Only*

12" Replacement Thermocouple

  • Heavy duty 8 Gauge
  • 12" long
  • Type K 2350F
  • Includes porcelain mounting block

  • $46.00
  • Availability: 3

Thermocouple 7" *Only*

7" Replacement Thermocouple

  • Heavy duty 8 Gauge
  • 7" long
  • Type K 2350F
  • Includes porcelain mounting block
  • $39.00
  • Availability: 3

Gauge Water Column Gas Pressure 0-15 1/4


Water column gas pressure gauge is an invaluable device for anyone wanting to establish a kiln firing schedule. It measures the gas pressure to the burners as an indication of how much gas is entering the kiln.


It is easily installed on the side of the gas shutoff valve and reads gas pressure on a calibrated scale from 0-15 inches of water column pressure 1/4" Nipple and  2 1/2" Dial #90267     LGFS115


Click Photo Twice for life size image.


  • $59.00
  • Availability: 5

Burner Mixer *Pin* 1/2" Orfc Lp 50

Replacement Burner Mixer *Pin* With LP orifice
  • $12.50
  • Availability: 2

Burner Mixer *Pin* with /Orfc Natural

Replacement Burner Mixer *Pin* With LP orifice
  • $12.50
  • Availability: 0

Orifice Venturi Natural Gas #28 tip

Replacement Orifice for Natural Gas #28 size (for sea Level)
  • $3.10
  • Availability: 6

Orifice Venturi Propane LP #38

Replacement Orifice for Propane #38 size (for sea Level)
  • $3.10
  • Availability: 4

Orifice Propane LP #50 tip

Orifice for propane at 5000+ feet. Fits the Venturi burner.
  • $3.10
  • Availability: 8

Burner Air Mixer (LP) 8" pipe

This burner is the industry standard. It has a completly adjustable primary air shutter adjustment. It fits standard 1/2" pipe fitting. 35,000 BTU. Comes with 8" pipe and LP orifice #32.
  • $45.50
  • Availability: 1

Burner Venturi Propane orifice

FS-122 VENTURI BURNER This burner is one of the most effective burners available for its price and size. It's tapered throat creates its own vacuum, thereby increasing the velocity of the flame through the burner. Cast into the tip of the burner is a flame retention nozzle that condenses the flame to its maximum heat capacity. This burner also has primary air shutter and a removable orifice for maximum burner adjustment. The total length of the burner is only 8", yet it yields approximately 75,000 B.T.U. per hour at 7" of water column pressure. Screws into a s ½ " pipe fitting For propane gas.
  • $54.00
  • Availability: 2

Burner Venturi Natural Gas

FS-122 VENTURI BURNER  For natural gas.
This burner is one of the most effective burners available for its price and size. It's tapered throat creates its own vacuum, thereby increasing the velocity of the flame through the burner. Cast into the tip of the burner is a flame retention nozzle that condenses the flame to its maximum heat capacity. This burner also has primary air shutter and a removable orifice for maximum burner adjustment. The total length of the burner is only 8", yet it yields approximately 75,000 B.T.U. per hour at 7" of water column pressure. Screws into a s ½ " pipe fitting For natural gas.
  • $59.00
  • Availability: 6

Post Kiln Brick Soap

Post or Kiln Brick
"Soap"
2 1/4" x 2 1/2" x 9" long
Good to 3000F, normally used as kiln posts in soda, gas or wood kilns
 

  • $9.23
  • Availability: 22

Cement Kiln / Brick Smoothset

Smoothset Thermal Ceramics refractory mortar

Smoothset™ is a lower cost, tacky, 2800°F (1538°C) mortar. Excellent for built-up shapes.

 

  • $2.38 per POUND
  • Availability: 49

Gas Shut Off Valve 1 1/4"

Gas Shut off valve 1 1/4"
  • $41.90
  • Availability: 1

Rigidizer Gallon

Rigidizer by the Pint, used to make kaowool stiff. Colloidal silica. Spray onto kaowool and allow to air dry. Can be used to make molds for glass slumping. Will not make the kaowool blanket rigid enough to hold its shape at cone 10, say as a kiln ceiling. Buy 8 Pints to get a gallon! 25% off pint price.
  • $43.12
  • Availability: 3

Rigidizer Pint

Rigidizer by the Pint, used to make kaowool stiff. Colloidal silica. Spray onto kaowool and allow to air dry. Can be used to make molds for glass slumping. Will not make the kaowool blanket rigid enough to hold its shape at cone 10, say as a kiln ceiling. Also available in gallons.
  • $8.30
  • Availability: 8

Thermocouple Dual Complete

Replacement Thermocouple for the Skutt high temperature Dual Input Digital Pyrometer.

This Thermocouple assembly comes with a Type K thermocouple and mounting block, 5 feet of thermocouple wire, and a pyrometer flange for mounting the thermocouple to the kiln. It includes a standard thermocouple plug that plugs into the Pyrometer.

  • Original Price: $45.50
  • You Save: $4.55
  • $40.95
  • Availability: 3

Pyrometer Digital w/Thermocouple Package

We have a new high temperature Dual Input Digital Pyrometer available. This Pyrometer comes with a Type K thermocouple(7 1/4" long) and mounting block, 5 feet of thermocouple wire, and a pyrometer flange for mounting the thermocouple to the kiln. The Pyrometer comes with a case that can be mounted to the wall or it has a flip out back that can be set on a table. Since it is "Dual Input" you can purchase an additional thermocouple package and monitor two kilns. It even remembers the minimum and maximum temperatures recorded in a firing. It is rated to Cone 10 with a plus or minus 0.4% of reading accuracy.
  • $125.00
  • Availability: 0


Items 1-25 of 25